Canon XEED WUX6000 Manuale Utente

Table of ContentsSafety InstructionsBefore UseOperationProjecting an ImageUseful Functions Available During a PresentationSetting Functions from Menus

10Safety InstructionsBefore installing and operating the projector, read this manual thoroughly.This projector provides many convenient features and f

107Customizing System Operation (System Settings)Operation Setting Functions from MenusRestoring Original Gamma Settings> [System settings] > [O

108Customizing System Operation (System Settings)Specifying HDMI Input> [System settings] > [HDMI In]Set the type of equipment which is connecte

109Customizing System Operation (System Settings)Operation Setting Functions from MenusSelect [Yes] on the screen for confirmation and press the OK bu

110Customizing System Operation (System Settings)Resetting the Air Filter Counter> [System settings] > [Other settings] > [Air filter counter

111Customizing System Operation (System Settings)Operation Setting Functions from MenusResetting to the Default Setting> [System settings] > [Ot

113Table of ContentsSafety InstructionsBefore UseOperationProjecting an ImageUseful Functions Available During a PresentationSetting Functions from Me

114Before InstallationPrecautions When Carrying/Shipping the ProjectorPrecautions for InstallationBe sure to read “Safety Instructions” and “For Safe

Before Installation115Installation and Maintenance Installation Do Not Use in the Following Environments• Locations with excessive humidity, dust, oi

Before Installation116 Be Careful of CondensationIf the temperature of the room rises suddenly, moisture in the air may condense on the projector len

Before Installation117Installation and Maintenance Installation Install Facing in the Correct DirectionWhen installing the projector facing upward or

11Safety InstructionsSafety InstructionsSafety PrecautionsWARNING:• THIS APPARATUS MUST BE GROUNDED.• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

118Installation ProcedureSetting Up the Projector Positioning the Projector in Front of the ScreenPlace the projector in front of the screen. Floor

Installation Procedure119Installation and Maintenance Installation Ceiling Mounting or Rear ProjectionYou can mount the projector on the ceiling (cei

Installation Procedure120Installing / Removing the Lens Unit Installing the Lens Unit1 Use a Phillips-head screwdriver and loosen the lamp cover scre

Installation Procedure121Installation and Maintenance Installation2 Loosen the cosmetic panel screw, then slide the cosmetic panel toward the rear to

Installation Procedure1225 Then turn the projector back over and remove the sleeve.6 Referring to the following illustration, insert the lens connecto

Installation Procedure123Installation and Maintenance Installation8 Insert the projector lens cable into the connector until a click sound is heard.9

Installation Procedure124 Removing the Lens Unit1 Perform steps 1 to 5 of “Installing the Lens Unit” (P120 – P122) to remove the sleeve.2 Disconnect

Installation Procedure125Installation and Maintenance InstallationRelationship Between Image Size and Projecting DistanceThe projected image size is d

Installation Procedure126Long Zoom LensRS-IL02LZ40 86 54 86 48 72 541.9 (6.2)3.2 (10.5)54 060 129 81 129 73 108 812.8 (9.2)4.8 (15.7)81 080 172 108 17

Installation Procedure127Installation and Maintenance InstallationUltra Long Zoom LensRS-IL04UL60 129 81 129 73 108 814.6 (15.1)9.0 (29.5)81 080 172 1

13Safety InstructionsSafety InstructionsNever push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage p

Installation Procedure128Wide Zoom LensRS-IL05WZ40 86 54 89 50 81 61 0.9 (3.0)1.3 (4.3)54 060 129 81 133 75 122 911.3 (4.3)1.9 (6.2)81 080 172 108 1

Installation Procedure129Installation and Maintenance InstallationLens Shift FunctionThe projector includes a lens shift function. Operation of the bu

Installation Procedure130Area Outside the Lens Shift RangeWith the Standard Zoom Lens, Long Zoom Lens, Ultra Long Zoom Lens, and Wide Zoom Lens, when

131Installation and Maintenance InstallationConnection ProcedureConnectable Equipment and Input TerminalsHDMI Use this name to select the image input.

Connection Procedure134 Connecting with an HDMI cable (Input signal type: [HDMI] P39) Outputting Audio to SpeakersIt is possible to output audio fro

Connection Procedure135Installation and Maintenance InstallationConnecting AV EquipmentConnect the projector and AV equipment.The description provided

Connection Procedure137Installation and Maintenance Installation Outputting Audio to SpeakersIt is possible to output audio from the projected images

Connection Procedure138Plugging the Projector InConnect the power cord to the projector and plug it in.Connect the ground terminal on the power plug t

139Installation and Maintenance InstallationStarting ProjectionStarting and Stopping Projection Starting ProjectionPress the POWER button on the remo

Starting Projection140 When “No signal” AppearsWith a notebook computer, the user must turn on the external monitor output. (P140)Press the INPUT but

Safety Instructions14AC Power Cord RequirementThe AC Power Cord supplied with this projector meets the requirements for use in the country you purchas

141Installation and Maintenance InstallationInstallation-Related Menu SettingsLocking Installation Settings> [Install settings] > [Positional lo

Installation-Related Menu Settings142• To hang the projector from the ceiling, use the optional bracket. Contact the Canon Customer Support Center for

Installation-Related Menu Settings143Installation and Maintenance InstallationPress the OK button to accept your setting and then press the MENU butto

Installation-Related Menu Settings144Specifying Keystone Correction> [Install settings] > [Keystone]Two types of keystone correction are availab

Installation-Related Menu Settings145Installation and Maintenance InstallationSpecifying Digital Image Shift> [Install settings] > [Digital imag

Installation-Related Menu Settings146Adjusting Image Registration> [Install settings] > [Professional settings] > [Registration]Adjusts color

Installation-Related Menu Settings147Installation and Maintenance InstallationSpecifying Vertical Projection> [Install settings] > [Professional

Installation-Related Menu Settings148• To lock (protect) the saved position, set [Positional lock] (P141) to [On].• [Load position] is not available u

Installation-Related Menu Settings149Installation and Maintenance InstallationSpecifying a Menu Position> [Install settings] > [On screen] >

Installation-Related Menu Settings150Showing/Hiding Input Status> [Install settings] > [On screen] > [Show input status]You can select whethe

15Safety InstructionsSafety InstructionsFederal Communication Commission NoticeMultimedia Projector, Model: WUX6000This device complies with Part 15 o

Installation-Related Menu Settings151Installation and Maintenance InstallationSpecifying the Menu Display Time> [Install settings] > [On screen]

Installation-Related Menu Settings152Showing/Hiding Filter Cleaning Warnings> [Install settings] > [On screen] > [Air filter warning display]

Installation-Related Menu Settings153Installation and Maintenance InstallationDisplaying Test Patterns> [Install settings] > [Test pattern]You c

Installation-Related Menu Settings154Projecting from Multiple Projectors at Once (Edge Blending)> [Install settings] > [Professional settings] &

Installation-Related Menu Settings155Installation and Maintenance InstallationHere, you can use the following settings in the edge blending menu.3 Set

Installation-Related Menu Settings1565 Use the remote control’s [ ] button to select [Start position], and use the [ ] / [ ] buttons to move the marke

Installation-Related Menu Settings157Installation and Maintenance Installation Advanced Instructions: Color AdjustmentIn overlapping projection, port

Installation-Related Menu Settings158 Advanced Instructions: Black Level AdjustmentIn overlapping projection, dark colors are projected with less int

Installation-Related Menu Settings159Installation and Maintenance InstallationHere, you can use the following settings in the edge blending menu.2 Sel

Installation-Related Menu Settings160 Advanced Instructions: Smoother Overlapping AreasAdjustments to areas A, B, and C may make the black level alon

Safety Instructions16This section describes the safety symbols used in this manual. Important projector safety information is identified by the follow

Installation-Related Menu Settings161Installation and Maintenance Installation2 Select [B-width], and use the remote’s [ ] [ ] buttons to specify the

162

163Table of ContentsSafety InstructionsBefore UseOperationProjecting an ImageUseful Functions Available During a PresentationSetting Functions from Me

164Network Connection OverviewConnecting the projector to a network enables you to control the projector from a computer and receive notification of p

165Installation and Maintenance Connecting to a NetworkCompleting Projector SettingsFrom the projector menus screen, network settings can be configure

Completing Projector Settings166Specifying the Network Password> [Network settings] > [Network password setting]You can set whether or not a pas

Completing Projector Settings167Installation and Maintenance Connecting to a NetworkRegistering a Network Password> [Network settings] > [Regist

Completing Projector Settings168Specifying the Network Function> [Network settings] > [Network function]You can turn the projector network funct

Completing Projector Settings169Installation and Maintenance Connecting to a NetworkSpecifying DHCP> [Network settings] > [Detailed settings] &g

Completing Projector Settings170Initializing Network Settings> [Network settings] > [Detailed settings] > [Network setting initialization] Yo

17Safety InstructionsSafety InstructionsPrecautions for UseAs this section contains important safety-related information, be sure to read the followin

Completing Projector Settings172Specifying Crestron RoomView> [Network settings] > [Crestron RoomView]Crestron RoomView enables centralized mana

173Installation and Maintenance Connecting to a NetworkCompleting Computer SettingsSpecifying an IP AddressFollowing is an explanation of how to set t

Completing Computer Settings174ExampleIP address: 192.168.254.1Subnet mask: 255.255.255.08 When finished, click the [OK] button, and then click the [C

175Completing Computer SettingsInstallation and Maintenance Connecting to a NetworkExampleIP address: 192.168.254.1Subnet mask: 255.255.255.07 When th

Completing Computer Settings176ExampleIP address: 192.168.254.1Subnet mask: 255.255.255.07 When the settings are completed, click the [OK] button and

177Completing Computer SettingsInstallation and Maintenance Connecting to a NetworkExampleIP address: 192.168.254.1Subnet mask: 255.255.255.05 Click [

Completing Computer Settings178The following information is displayed.* For details on downloading the Networked Multi-Projection (NMPJ) application,

179Completing Computer SettingsInstallation and Maintenance Connecting to a NetworkThe projector settings screen is displayed in the web browser. Net

Completing Computer Settings1803 A confirmation window appears. Check the contents and if they are correct, click [Apply].The settings are applied to

181Completing Computer SettingsInstallation and Maintenance Connecting to a NetworkSetting Basic Information [Network]From [Network] in the settings s

Safety Instructions18Pay attention to the following points regarding the power source, power plug and handling of the connector. Failure to do so may

Completing Computer Settings182Specifying Networked Multi-Projection Settings: [NMPJ Password]From [NMPJ Password] in the settings screen, you can spe

183Completing Computer SettingsInstallation and Maintenance Connecting to a NetworkSetting Up Email [Mail]From [Mail] in the settings screen, you can

Completing Computer Settings184Mail Authentication Settings [Mail auth]From [Mail auth] in the settings screen, you can configure the settings for aut

185Completing Computer SettingsInstallation and Maintenance Connecting to a NetworkSending a Test Mail [Send test mail]From [Send test mail] in the se

Completing Computer Settings186Setting Projector Information [Projector info.]From [Projector info.] in the settings screen, you can enter relevant co

187Completing Computer SettingsInstallation and Maintenance Connecting to a NetworkSetting PJLink [PJLink]From [PJLink] in the settings screen, you ca

Completing Computer Settings188Setting ErrorsWhen a setting-related error occurs, the error name is displayed on the screen, and a “!” mark is display

189Completing Computer SettingsInstallation and Maintenance Connecting to a NetworkResetting Network Settings to the Default Settings1 Perform steps 1

195Cleaning the Projector and the Air FilterInstallation and Maintenance Maintenance• If the air filter cleaning screen is displayed when turning on t

196Replacing the Air FilterFollow the procedure below when replacing the air filter.1 Turn off the projector power and remove the power plug.2 Hook yo

19Safety InstructionsSafety InstructionsPay attention to the following points regarding installation and handling of the projector. Failure to do so m

197Installation and Maintenance MaintenanceReplacing the LampWhen the usage time of the lamp exceeds a certain amount of time, the following message (

Replacing the Lamp198Replacement LampThis projector uses the following lamps.Lamp part no.: RS-LP09Contact the Canon Customer Support Center when purc

199Replacing the LampInstallation and Maintenance MaintenanceReplacing the Lamp1 Turn off the projector power and remove the power plug.2 Loosen one s

Replacing the Lamp2007 Select [Reset] > [Yes] to reset the lamp counter.• It is recommended that you also replace the air filter when you replace t

201Table of ContentsSafety InstructionsBefore UseOperationProjecting an ImageUseful Functions Available During a PresentationSetting Functions from Me

202TroubleshootingLED Indicator MeaningsWhen there is a problem with the projector, the LED indicator on the side of the projector illuminates or flas

203TroubleshootingAppendix Other InformationSymptoms and Solutions You Cannot Turn on the ProjectorWARNING (only) flashes 5 times repeatedly.Faulty p

Troubleshooting204 You Cannot Project an Image from the ProjectorThe lens connector is not attached correctly.The lens cable is not connected to the

205TroubleshootingAppendix Other Information There is no SoundThe external monitor output is not set on the notebook computer correctly.Turn on the e

Troubleshooting206 The Projected Image Is BlurredCause CountermeasureThe image is out of focus.Adjust the focus. (P44)The distance to the screen is t

Safety Instructions20Precautions on the LampThis projector uses a high-pressure mercury lamp, which must be handled carefully and correctly as describ

207TroubleshootingAppendix Other Information You Cannot Project an Image Appropriately The Projector Power Turns OffCause CountermeasureThe projecte

Troubleshooting208 You Cannot Operate the Remote ControlCause CountermeasureBatteries are not installed properly or they have run out.Check whether b

209Appendix Other InformationRelationship between Aspect and Screen AspectThis section describes the relationship between screen aspect (P48) and aspe

Relationship between Aspect and Screen Aspect210 When the image is projected on a 16:9 screen When the image is projected on a 4:3 screenAspect rati

211Relationship between Aspect and Screen AspectAppendix Other Information When projecting on a 16:10 screen in the aspect ratio of the connected dev

Relationship between Aspect and Screen Aspect212 When projecting on a 4:3 screen in the aspect ratio of the connected deviceAspect ratio of connected

213Appendix Other InformationDisplayed Test PatternsTo access the test pattern menu, from the [Install settings] menu, select [Test pattern] > [On]

214Supported Signal TypesThis projector supports the following signal types.If your computer or AV equipment is compatible with any one of these signa

215Supported Signal TypesAppendix Other InformationHDMIConnecting to a computerConnecting with AV equipmentComponent* The specifications in the table

216Product Specifications ProjectorModel name WUX6000Display system RGB liquid crystal systemOptical systemColor separation by dichroic mirror / pola

23For Safe UseFor Safe UsePay attention to the following points when carrying or transporting the projector.• This projector is a precision instrument

217Product SpecificationsAppendix Other Information*1When using a Standard Zoom Lens (RS-IL01ST). Varies depending on the type of lens unit.*2When lam

Product Specifications218 Specification of Each Lens Unit (Option)For details about the amount of lens shift, refer to “Lens Shift Function” on page

219Product SpecificationsAppendix Other InformationFor details about the amount of lens shift, refer to “Lens Shift Function” on page 129.Name Short F

229Menu ConfigurationImage Adjustment MenuSlideshow intervalUSBP81[--:--]:[60:00]Split screenDigital PC / Analog PC-1/2 / HDMI / Component / LAN / USB

Menu Configuration230Factory default settings are set according to the following conditions.*1• [Off] by default when HDMI ([HDMI In]) is [Computer],

Menu Configuration231Install Settings MenuPositional lock Off* P141OnImage flip H/V None* P141Ceiling mountedRearRear, Ceiling mountedScreen aspect16:

Menu Configuration232System Settings MenuLens - Position Load position 1 - 3 P147Save position 1 - 3Lens shift resetScreen color Normal* P148Greenboar

233Menu ConfigurationPower management mode Disabled P98Lamp offStandby*Power management duration 5 min. P9910 min.15 min.*20 min.30 min.60 min.Direct

Menu Configuration234Network Settings MenuAudio in terminal selectHDMI Off P106Audio in 1Audio in 2HDMI*Digital PC Off P106Audio in 1*Audio in 2Analog

235Menu ConfigurationInformationNetwork function Off* P168OnDetailed settingsIP address P168Gateway addressP168MAC address P168DHCP Off* P169OnTCP/IP

For Safe Use24Pay attention to the following points when installing or using the projector.• Do not touch the lens with bare hands. Doing so may resul

©CANON INC.2014CANON INC.30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, JapanU.S.A.CANON U.S.A. INC.One Canon Park, Melville, New York 11747, U.S

25Open Source SoftwareOpen Source SoftwareThe product contains Open Source Software modules. For details, see “ThirdPartySoftware.pdf” (Third-Party So

26

27Table of ContentsSafety InstructionsBefore UseOperationProjecting an ImageUseful Functions Available During a PresentationSetting Functions from Men

28Supplied AccessoriesCheck that the following accessories have been supplied with the projector.• Remote control • Batteries for the remote control(A

29Before UsePreparing the Remote Control Installing Remote Control Batteries• If buttons on the remote control are inoperative when you attempt to op

Preparing the Remote Control30 Remote Control Operating RangeThe remote control is an infrared type. Point it at the infrared remote receiver on the

31Before UsePart NamesProjector Front Side Rear Side Bottom SideTerminals and connectorsInfrared remote receiver (P30)Lens unitAir intake ventPower

Part Names32Remote controlThe projector can be operated using buttons on the remote control or the side control on the main unit.The remote control al

33Part NamesBefore UsePress D.SHIFT/KEYSTONE to correct keystone distortion.• Moves the image up, down, left, or right when the screen aspect setting

Part Names34Side control(2)(1) LED indicators (P35)The projector status is shown by the LED indicators (off / lit / flashing).For indicator status, re

35Part NamesBefore Use LED Indicator DisplaysThe LED indicators flash or illuminate to indicate the operating status of the projector.If WARNING is o

Part Names36Input Terminal(1) Terminal for wired remote control (REMOTE) (P30)Connects to an optional wired remote control (RS-RC05).(2) AUDIO IN term

37Table of ContentsSafety InstructionsBefore UseOperationProjecting an ImageUseful Functions Available During a PresentationSetting Functions from Men

39Operation Projecting an ImageStep 2 Select an Input SignalSelect the input signal in the [Input] menu when you want to project a digital PC or AV eq

Step 2 Select an Input Signal40Selecting an Input Signal1 Press the INPUT button to display the window shown below.The currently active input signal i

41Operation Projecting an ImageStep 3 Adjust the ImageSetting the Display Resolution of the ComputerBased on the maximum resolution of the projector,

Step 3 Adjust the Image42 Windows Vista1 Open the [Control Panel] from the start menu, then select [Appearance and Personalization] - [Adjust screen

43Step 3 Adjust the ImageOperation Projecting an ImageAuto PC AdjustmentIf the image display is shifted or there is flickering of the screen when [Ana

Step 3 Adjust the Image44Focusing, Resizing, or Moving the ImageAdjusting Image FocusTo adjust the focus, press the FOCUS button on the remote control

45Step 3 Adjust the ImageOperation Projecting an ImageAdjusting Image SizeThe size of the projected image can be adjusted by pressing the ZOOM button

Step 3 Adjust the Image46Adjusting the Image PositionTo adjust the screen position up, down, left, or right, press the LENS-SHIFT button on the remote

47Step 3 Adjust the ImageOperation Projecting an Image Resetting the PositionThe lens position after movement with the lens shift function is not ret

48Step 4 Select an Aspect Ratio (Screen Aspect) Matching the ScreenSelect an optimum aspect ratio of the projected image (screen aspect) or an optimum

Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen5016:9 D. image shiftSelect this when you use a screen with an aspect ratio of 16:9.K

51Step 4 Select an Aspect Ratio (Screen Aspect) Matching the ScreenOperation Projecting an Image4 Use the [ ] / [ ] buttons to move the image up or do

Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen524 Use the [ ] / [ ] buttons to move the image.5 When the image fits the screen, pre

5Quick Reference GuideThis Quick Reference Guide will help you find functions that make full use of the projector and are useful for producing an attr

53Step 4 Select an Aspect Ratio (Screen Aspect) Matching the ScreenOperation Projecting an Image4:3The image is projected using an input signal aspect

54Step 5 Correct the Image DistortionAdjusting Keystone DistortionTo correct keystone distortion, press the D.SHIFT/KEYSTONE button.Use the remote con

55Step 5 Correct the Image DistortionOperation Projecting an Image2 Press the pointer buttons to adjust the dimensions.3 When keystone distortion has

Step 5 Correct the Image Distortion562 Press the pointer button of the corner for correction, and then press the OK button.3 Press the pointer buttons

57Operation Projecting an ImageStep 6 Select the Image Quality (Image Mode)You can select an image mode to suit the projected image.In each image mode

Step 6 Select the Image Quality (Image Mode)58 Selecting an Image ModePress the IMAGE button on the remote control to select.The image mode changes e

59Operation Projecting an ImageStep 7 Set Power-Saving SettingsNext, complete power-saving settings as needed.The following four settings are availabl

60Step 8 Turn the Projector Off1 Press the POWER button to display the window shown below.2 When this window is displayed, press the POWER button agai

61Table of ContentsSafety InstructionsBefore UseOperationProjecting an ImageUseful Functions Available During a PresentationSetting Functions from Men

62Useful Presentation FunctionsTemporarily Blacking Out an ImageUseful when:• You have finished the presentation.• You want to divert attendees’ atten

6Table of ContentsHow to Use This Manual... 2Projector Highlights... 4Quick Reference Guide ... 5Safety In

Useful Presentation Functions63Operation Useful Functions Available During a PresentationAdjusting the VolumeUseful when:• You want to adjust the volu

65Operation Useful Functions Available During a PresentationProjecting Images on a USB Flash DriveImages stored on a USB flash drive in the projector

66Projecting Images on a USB Flash Drive4 Use the pointer buttons to select a file, and then press the OK button to project the image.Press the [ ] /

67Operation Useful Functions Available During a PresentationSplit-Screen DisplayTwo input images can be projected side by side. This is split-screen d

68Split-Screen Display4 Use the [ ] / [ ] buttons to select [On], and then press the OK button.5 If or is displayed in the center of the image are

Split-Screen Display69Operation Useful Functions Available During a PresentationTo exit split-screen display, select [Input settings] tab > [Split

70

71Table of ContentsSafety InstructionsBefore UseOperationProjecting an ImageUseful Functions Available During a PresentationSetting Functions from Men

72Using MenusUse the menus to set the operation of the projector in detail.Menu ConfigurationThe menu screen is divided into 6 tabs as shown below.Men

Using Menus73Operation Setting Functions from MenusBasic Menu Operations1 Press the MENU button to display the menu window.2 Press the [ ] / [ ] butto

7Table of ContentsTable of ContentsSelecting an Input Signal(Analog PC Input)... 76Adjusting the Input Signal(Total dots

74Using MenusAdjusting with the [ ] / [ ] buttons Example: Contrast (P86)Selecting from a different screen (1) Example: Menu position (P149)Select

75Operation Setting Functions from MenusSetting Display Status (Input Settings)Selecting the Aspect> [Input settings] > [Aspect] You can select

76Setting Display Status (Input Settings)Setup Using Auto PC> [Input settings] > [Auto PC]Automatically adjusts display position misalignment an

77Setting Display Status (Input Settings)Operation Setting Functions from MenusAdjusting the Input Signal(Total dots)> [Input settings] > [Input

78Setting Display Status (Input Settings)Adjusting the Input Signal(Horizontal / Vertical position)> [Input settings] > [Input signal settings]

79Setting Display Status (Input Settings)Operation Setting Functions from MenusAdjusting HDMI Input Level> [Input settings] > [HDMI input level]

80Setting Display Status (Input Settings)Specifying HDMI Overscan> [Input settings] > [HDMI over scan]When projecting images in videos via HDMI,

81Setting Display Status (Input Settings)Operation Setting Functions from Menus• [Film/auto] is the factory default.• Select [Off] when flickers and h

82Setting Display Status (Input Settings)Specifying Split-Screen Display> [Input settings] > [Split screen] You can project two input images sid

83Operation Setting Functions from MenusAdjusting Image Quality (Image Adjustment)Specifying Image Priority in Split-Screen Mode> [Image adjustment

Table of Contents8Relationship Between Image Size and Projecting Distance ... 125Lens Shift Function ...

84Adjusting Image Quality (Image Adjustment)Specifying the Image Mode> [Image adjustment] > [Image mode]You can select an image mode (P57) suita

86Adjusting Image Quality (Image Adjustment)Adjusting Brightness> [Image adjustment] > [Brightness]You can adjust the brightness of images.When

87Adjusting Image Quality (Image Adjustment)Operation Setting Functions from MenusAdjusting Sharpness> [Image adjustment] > [Sharpness]You can a

88Adjusting Image Quality (Image Adjustment)Adjusting Colors> [Image adjustment] > [Color adjustment]You can adjust the color depth and hue of i

89Adjusting Image Quality (Image Adjustment)Operation Setting Functions from MenusAdjusting to the Ambient Light(Ambient Light)> [Image adjustment]

90Adjusting Image Quality (Image Adjustment)Reducing Image Noise(Random noise reduction)> [Image adjustment] > [Advanced adjustment] > [Rando

91Adjusting Image Quality (Image Adjustment)Operation Setting Functions from MenusReducing Image Noise(Mosquito noise reduction)> [Image adjustment

92Adjusting Image Quality (Image Adjustment)Correcting Memory Color> [Image adjustment] > [Advanced adjustment] > [Mem. color correct]Enhance

93Adjusting Image Quality (Image Adjustment)Operation Setting Functions from Menus• [Off] is the factory default.• The adjustments you have made are s

94Adjusting Image Quality (Image Adjustment)• The adjustments you have made are stored as adjusted values for the input signals and image mode of the

9Table of ContentsTable of ContentsRelationship between Aspect and Screen Aspect ... 209Displayed Test Patterns ... 21

95Adjusting Image Quality (Image Adjustment)Operation Setting Functions from MenusSpecifying the Lamp Mode> [Image adjustment] > [Lamp mode]Redu

96Customizing System Operation (System Settings)Registering User Logos> [System settings] > [User screen settings] > [Logo capture]Registers

97Customizing System Operation (System Settings)Operation Setting Functions from MenusNo Signal Screen> [System settings] > [User screen setting

98Customizing System Operation (System Settings)Selecting a Logo at Startup> [System settings] > [User screen settings] > [Projector on]You c

99Customizing System Operation (System Settings)Operation Setting Functions from MenusSpecifying Power Management Duration> [System settings] >

102Customizing System Operation (System Settings)Assigning a Channel for Remote Control> [System settings] > [Remote control channel]When using

103Customizing System Operation (System Settings)Operation Setting Functions from MenusReducing Motion Blur> [System settings] > [Motion blur re

104Customizing System Operation (System Settings)Requiring a Password for Operation> [System settings] > [Other settings] > [Password setting

105Customizing System Operation (System Settings)Operation Setting Functions from MenusSetting a Password> [System settings] > [Other settings]

106Customizing System Operation (System Settings)Selecting Audio Input> [System settings] > [Other settings] > [Audio in terminal select] You